OT FIT 150 /220-240/24 PC
Áreas de aplicación
- Apto para luminarias de las clases de protección I y II
- Hospitality decorative lighting, night light
- Restaurants decorative lighting
- Shops decorative lighting, shelf lighting
- Residential cove lighting, under cabinet lighting
Datos técnicos
Datos eléctricos
Tensión de entrada nominal
220 240 V
Frecuencia de red
50/60 HZ Hz
Tensión de entrada
198 264 V
Distorsión armónica total
< 15 %
Factor de potencia λ
> 0,95
Efficiency in full-load
92 %
Pérdida de potencia del equipo
13 W
Corriente de encendido IP
< 60 A
Nº de ECE máximos con automátic 10 A (B)
2
Nº de ECE máximos con automátic 10 A (B)
3
Nº de ECE máximos con automátic 16 A (B)
4
Nº de ECE máximos con automátic 16 A (B)
6
Resis. a la sobretensión (L/N-tierra)
2 kV
Tensión de aislamiento (L-N)
1 kV
Tensión de salida
24.2 V
Potencia de salida
60.5...151.3 W
Potencia de salida máxima
151.3 W
Aislamiento galvánico
SELV
Output PWM frequency
3 k Hz
Dimensiones y peso
Distancia entre taladros longitud
159.5 mm
Peso del producto
580,00 g
Sección de cable, entrada
0,75 1,5 mm²
Sección de cable, salida
0,75 1,5 mm²
Long aislamiento parte de la entrada
7 8 mm
Long aislamiento parte de la salida
7 8 mm
Distancia entre taladros anchura
66 mm
Ancho
76,0 mm
Largo
170,0 mm
Alto
30,0 mm
Colores y materiales
Material de la carcasa
Plastic
Temp. y condiciones de funcionamiento
Margen de temperatura ambiente
-20 +45 °C
Temp. máx. en el punto de prueba tc
80 °C
Temp. máx de la carcasa en caso de fallo
110 °C
Temperatura de almacenamiento
-20 80 °C
Humedad en el aire
5 85 %
Duración de vida
ECE vida útil
50000 h
Capacidades
Regulable
Sí
Interfaz DIM
Phase Cut
Margen de regulación
3 100 %
Regulador
PWM
Protección contra sobrecalentamiento
Sí
Protección contra sobrecarga
Sí
Protección contra cortocircuito
Sí
Prueba de no carga
Sí
Apto para luminarias con clase de prot.
I
Tipo de conexión, entrada lateral
Conexión fija (clema)
Tipo de conexión, salida lateral
Conexión fija (clema)
Control interface
Trailing edge dimmer recommended
Number of channels
1
Programming
Tuner4TRONIC
No
Certificados & Normas
Símbolos de homologación
CE / ENEC / CCC / RCM / UKCA / EAC / SELV / CB
Normas
Según EN 61347-1/Según EN 61347-2-13/Según EN 55015/Según EN 61547/Según EN 60598-1/Según EN 62384/CISPR 15/EN 55015
Tipo de protección
II
Tipo de protección
IP20
Datos logísticos
Número estadístico de material
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
16-06-2023
Primary Article Identifier
4062172237642
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
c8d942cb-c0d0-46d9-8c20-823a1003a630
Información de embalaje
EAN |
Unidad |
Pieza |
Dimensiones |
Peso |
Volumen |
---|---|---|---|---|---|
4062172237642 |
UNV
| 1 | 170mm x 76mm x 30mm | 580.00g | 0.39dm³ |
4062172237659 |
VS
| 10 | 400mm x 187mm x 99mm | 6142.00g | 7.41dm³ |
Descargas
Fichas técnicas
Accesorios opcionales
Más sobre la familia de productos
Características del producto
- 24 V constant output voltage
- SELV
- Wide Ta range -20 +50 ℃
- Lifetime 50 000 h at tc max
- Rango de regulación: 3 100 % de flujo luminoso
- Recommended to Use Trailing Edge dimmer
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Productos
Nombre del producto |
|
|
|
|
|
Fichas técnicas | ||
---|---|---|---|---|---|---|---|---|
![]() |
OT FIT 36 /220-240/24 PC
|
2.42 36.3 W | Sí | 103,0 mm | 67,0 mm | 29,5 mm | ||
![]() |
OT FIT 75 /220-240/24 PC
|
24.2...75.8 W | Sí | 110,0 mm | 76,0 mm | 30,0 mm | ||
![]() |
OT FIT 150 /220-240/24 PC
|
60.5...151.3 W | Sí | 170,0 mm | 76,0 mm | 30,0 mm |